How to enter cline blade media 7000s

[HiTecK]

To edit CSInfo.txt
------------------

The file lists all the slots from the Server List menu on the box, 24 slots total.

Therefore to edit just change details to your account details using text editor like notepad, eg. looks like this:-





slot0 =
{
name: Connection_0
ip: test.ip.com <<<<<<< put here your server address
user: username <<<<<<< put here your username/ID for server
password: password <<<<< put here your password for server
protocol: cccam <<<<<<< write here either cccam or newcamd525
deskey: 01 02 03 04 05 06 07 08 09 10 11 12 13 14 <<<<<< only used for newcamd525, ignore for cccam
filtermode: auto
filterindex: 0
port: 12000 <<<<<<< write here your port for server
timeout: 3
}





If you are given cline its format is:

C: [server address] [port] [username/ID] [password]

When you have finished adding address/port/usernameID/password, save the file, put on USB key, insert USB key to box and go to:

MENU> UTILS> DOWNLOAD, select CSInfo file and press OK.

Finished.

----------------------------------------




To Bootflash.
-------------

To flash box without connecting to TV and without remote control, put latest firmware file on Usb key, insert in box and turn box on while holding ON button down on front panel.

Box will now flash from boot.

 

[goldmember79]

I am a newby here - sorry for the lack of knowledge.

I have a Blade Receiver which is set up to receive Tring Sports for football. Can I also add another cline so I can get SLY UK also? Will my dish move automatically to Astra as it is motorised?
Thanks for help................... :p

 

[bobby123]

yes mate you can add another cline for sky just download 28.2 e channel list with your blade

 

[goldmember79]

do i then just pop in the following details for the sly cline info?

name: Connection_0
ip: test.ip.com <<<<<<< put here your server address
user: username <<<<<<< put here your username/ID for server
password: password <<<<< put here your password for server
protocol: cccam <<<<<<< write here either cccam or newcamd525
deskey: 01 02 03 04 05 06 07 08 09 10 11 12 13 14 <<<<<< only used for newcamd525, ignore for cccam
filtermode: auto
filterindex: 0
port: 12000 <<<<<<< write here your port for server
timeout: 3

 

[bobby123]

this is to add cline on blade media

1st press 9991
then you get server list
then press ok button you will be asked for number again which is 9991
then you are in server editor ok so it is like this
1....name call this what you like
2....protocal....... you can select cccam or newcamd by pressing the ok button
3....timeout....... no need to touch
4....flitermode..... no need to touch
5....filterlist....... blanked out
6....id.................this is username server owner gives you
7....password.......password from server owner
8....des-key.........blanked out no need to touch
9....address.........this is addy of server owner
10...port..............port number of server owner

when you re adding details into each section there maybe capital letters and lowercase and numbers to enter in order to add these on the left hand side you will see
A-Z
a-z
others

as you are adding details in each section if you need to change from one to other then you press red button and that changes you from caps to lower case to numbers and back again

once you have added details press exit and save details

then press red button to connect or green button to disconnect

you need to enter details correct just 1 letter wrong or caps instead of lowercase you wont connect

 

[zippy123]

good morning m8t i have tried to put the cline on my blade 7000 but the file will not open ive emailed another card sharer and would be grateful if you could pm me with a step by step guide to help me because i must be doing something wrong i look forward to hearing from you thanks:anyonethere:

 

[bobby123]

it's like this
server mycline.ip.tv
username xfgxffgxf
port 13000
password ggdgfgn

 

[akbarirfan]

Hi,

I have been given an N line in this format: protocol - IP/host - port - USER - PASS - DES-key

How would I use this?

Thanks

Just looked at goldmembers' post, I think I have worked it out.

Where does the physical file come from?

Thanks

 

[hunter1010]

You see i'm gagging to get sat but this just blows me away i can see hi-tek and bobby are trying there best here to explain this but shit its hard, think wahts hard is all the abbreviations as a newby to sat this is just like german! :nerd:

 

[Zito]

Connected and what to do next?

Hi everyone

I'm in Server List now and I have entered a cline and it says connected. What do I have to do next to watch these channels.

Thanks

 

[bilbo123]

If it says connected, thats it, just watch the channels you want.

 

[stigie]

on the blade if a port you are given only has 4 numbers how do you add them ?

 

[bilbo123]

put a zero in front of the 4 numbers mate

 

[stigie]

cheers that simple :woohoo:

 

[silversurfer]

how do I get into the server list on blade 7000s

 

[bees]

You need patched firmware, then press 9991
from any channel on your remote.

Have a read here

 

[thomaskieron]

Hi All,

9991 does not bring anything on my BM7000s

9992 brings up the Select CAS menu fine.

Firmware is BM7000s-24-03-14-8ex
H/W Version 1.00
Boot Version 5.30
CH Version F015

I already have my csfile.txt on a usb stick, but have no way to install it....

HELP!!!