1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Wooshbuild 5 on H2H All good

Discussion in 'Zgemma Star H.2H' started by D12UNC, Dec 31, 2016.

  1. lefty940

    lefty940 Registered

    7
    0
    1
    Male
    having a great start i cant get the box to flash it just goes from boot then numbers count up its a kingston usb stick pretty sure i have the right file for it
     
  2. ste

    ste TK Veteran

    Try formatting the usb stick - check also there's a force file within the file within the zgemma folder you're putting on the usb drive.
     
  3. lefty940

    lefty940 Registered

    7
    0
    1
    Male
    i got going now i was following a youtube video to st up the woosh build but its different to the screens i got lol im not stuck quite yet lol
     
  4. lefty940

    lefty940 Registered

    7
    0
    1
    Male
    where i am now stuck is i did not get the welcome to wooshbuild screen where it scans the channels so i dontthink i geot the full menus
     
  5. ste

    ste TK Veteran

    Are you using satellite and cable on this box or just one or the other? if you're only using one then you need to disable the other before scanning ... whilst you're in tuner config, also check you have the network i / area id entered for tuners that are going to be in use then once you've done this you need to go into menu / set up / service searching / autobouquetsmaker then you need to choose providers - make sure what you're using (s*y / VM) is enabled or disabled then do a manual scan with yellow button I believe it is.
     
  6. lefty940

    lefty940 Registered

    7
    0
    1
    Male
    thanks mate i have the free channels on now just got to work out the lines i will do that in the morning fried brain now lol thanks again
     
  7. ste

    ste TK Veteran

    lefty940 likes this.
  8. renaultuk

    renaultuk Registered

    30
    1
    8
    Male
    {Mechanic
    Notts
    Hi I've been following your thread installing wooshbuild brill thread but I cannot see the on installing line as the link goes to a error page if you still got it can I have it please
     
  9. ste

    ste TK Veteran

  10. Shaikhy91

    Shaikhy91 Registered

    14
    0
    1
    If I'm running both sky and virgin lines. Sky for fta and virgin for subscription, how do i go about getting autobouquet and epg for both?
     
  11. ste

    ste TK Veteran

    In ABM config, change add provider prefix to bouquets to yes then re-scan.
     
  12. Shaikhy91

    Shaikhy91 Registered

    14
    0
    1
    I have both bouquet and epg running, however the virgin epg is only showing on some channels. Any advice how to get them all to show
     
  13. ste

    ste TK Veteran

    You need to run epg importer from portal
     
  14. melvis

    melvis Registered

    68
    5
    8
    Wooshman, which file should I download for the H2H? I have tried Zgemma HS, H2S - WB v6 but it has Ae2 and not ABM, and Zgemma S, 2S, H1*, H2* but that will not flash. Should it be one of the H5/H3 files? I do not see a H2H on your download site.

    Cheers.
     
  15. ste

    ste TK Veteran

    It's second from bottom... should have gone to specsavers :D
     
    melvis and wooshman like this.
  16. melvis

    melvis Registered

    68
    5
    8
    Thanks. Silly me and I definitely need to go to specsavers as I looked on 3 different occasions. :)
     
  17. wooshman

    wooshman VIP Member Forum Supporter

    4,786
    1,871
    133
    {Bodge Builder
    UK
    You need to download the H2H version, it is on the site with the others. Second from the bottom - not sure why it is that far down, maybe I was having an off day.

    I was late to the party :)
     
    melvis likes this.
  18. melvis

    melvis Registered

    68
    5
    8
    Next silly question. Is it possible for me to add the WBconfig to the H2H image that I just downloaded and installed and the SkyWB skin?
     
  19. wooshman

    wooshman VIP Member Forum Supporter

    4,786
    1,871
    133
    {Bodge Builder
    UK
    it is already installed. YOu have downloaded basebuild - you need to go through that to install WooshBuild.

    WooshBuild has SkyQ, VM 1.5 and SkyWB all by chabs. Any you want are in the Skins section of plugins if not already installed.
     
  20. melvis

    melvis Registered

    68
    5
    8
    That's it. I need sleep. I copied the wrong zgemma folder to the USB stick. Sorry for bothering ye all and i'll start afresh tomorrow :(