Adding Line To Technomate

Tony Batty

Newbie
Thread starter
I have downloade the file tm 5402 and the software |File Zilla please explain what i do with them and how i get them into my receiver
 

pabloescaban

VIP Member
TK Supporter
I have downloade the file tm 5402 and the software |File Zilla please explain what i do with them and how i get them into my receiver
Ive been informed you can't use FileZilla to send files to that box like you can with other boxes, you must have to install files via usb
 

manic01

Newbie
Manual install, no usb install, the procedure posted by mike124 earlier was from a post of mine on another forum, its the only way atm.
Any new stb loading patches will not get the forever server its been removed when stb is registered.
Its an expensive 1080 stb.
 

manic01

Newbie
If it's just a normal C line for sat or euro sat it goes in Ccam.cfg file, use FileZilla to send it to the box from your computer/laptop, takes two minutes
Its non linux so that doesn't work, older versions of 5402 allowed usb load but this is a 5402 in name only very poor relation.
 

manic01

Newbie
To enter lines

You manually enter details in server details.
(Server details are below BISS in menu)



Menu

Installation

Server (Server details are below BISS in menu)

Select slot 1

Press GREEN to enable server

Enter your details ( IP/URL - PORT - Des Key (if req) - User name - Password - Server type Newcs/Mgcamd/Gscam or CCCam)

Select Confirm and press OK

Select SAVE when prompted

Do this for all lines you have on different slots where need
 
Last edited:

kegnkiwi

TK Veteran
Just a question i keep reading about losing the forever server, is this the same forever server that the viarks etc can connect too? If it is is it not better to keep to the older patches?
 

Ferret.

TK Veteran
Just a question i keep reading about losing the forever server, is this the same forever server that the viarks etc can connect too? If it is is it not better to keep to the older patches?
It was the same but TM in there ultimate wisdom changed it to the basic funcam server which is now offline also.

Not worth anywhere near the money this box. It could of been a good box. They bottled it server wise.

@manic01 put some real effort in ironing out the niggles the box had with TM directly it was starting to look like a contender till TM removed Forever. Now it just a £40 box.
 

kegnkiwi

TK Veteran
It was the same but TM in there ultimate wisdom changed it to the basic funcam server which is now offline also.

Not worth anywhere near the money this box. It could of been a good box. They bottled it server wise.

@manic01 put some real effort in ironing out the niggles the box had with TM directly it was starting to look like a contender till TM removed Forever. Now it just a £40 box.
What a shame :(
 

manic01

Newbie
It was the same but TM in there ultimate wisdom changed it to the basic funcam server which is now offline also.

Not worth anywhere near the money this box. It could of been a good box. They bottled it server wise.

@manic01 put some real effort in ironing out the niggles the box had with TM directly it was starting to look like a contender till TM removed Forever. Now it just a £40 box.
For £99 lol, Has scart and also rs232 if you have a time machine handy and need them :unsure:
 
Last edited:

manic01

Newbie
I had the old Technomate 5402 which went belly up I could put cc cam lines in this when i bought the updated version I fouind i could not put them in this can anybody in the northwest help I am willing to travel as far north as Carlisle and as far south as Manchester to get this sorted if not can somebody download the software needed to a memory stick and explain how I install it in my box it is the Technomate 5402 MK4
How did you get on with this?
 

Tony Batty

Newbie
Thread starter
To enter lines

You manually enter details in server details.
(Server details are below BISS in menu)



Menu

Installation

Server (Server details are below BISS in menu)

Select slot 1

Press GREEN to enable server

Enter your details ( IP/URL - PORT - Des Key (if req) - User name - Password - Server type Newcs/Mgcamd/Gscam or CCCam)

Select Confirm and press OK

Select SAVE when prompted
I am unable to edit the top Line IP/URL to put my friends testlines in I am making the long journey from Morecambe to Newcastle next week to get the Satelitte Superstore where I bought it t to to re enter all the original Software as I have lost the forever server but they are refusing to enter the software that enables me to enter lines so when that has been done any help entering the software for this would be greatly appreciated I am willing to travel as far north as Carlisle and as far south as Manchester West Yorkshire would be ok too please IM me if you can help its a Technomate 5402 MK 4
Do this for all lines you have on different slots where need
 

Tony Batty

Newbie
Thread starter
Re the problem with my box I am unable to edit the top Line IP/URL to put my friends testlines in so I am making the long journey from Morecambe to Newcastle next week to get the Satelitte Superstore where I bought it t to to re enter all the original Software as I have lost the forever server but they are refusing to enter the software that enables me to enter lines so when that has been done any help entering the software for this would be greatly appreciated I am willing to travel as far north as Carlisle and as far south as Manchester West Yorkshire would be ok too I know the job will only take 15 minutes at the most but the trip would be worth it
 
Top