Help me with glitching!

Showboat

Newbie
Hi, i have glitching on my h2h, using the openatv 5.3 build.

I get the glitching on the fta channels as well, so not a supplier problem.
When i remove the splitter i don't get any glitching... When i use the splitter and dont connect the router i dont get any glitching, as soon as i connect the router to the splitter it starts to glitch.

I have tried 3 different cables and 3 different splitters!

The router also has a 6db attentuator attached to it, so i think the signal must be strong enough.
Any advice?

These are the results of the router with the attenuator attached to it only (not the splitter).

Downstream bonded channels
Channel Frequency(Hz) Power SNR Modulation Channel ID
(dBmV) (dB)
1 2.99E+08 -4.9 38.9 256 qam 21
2 3.23E+08 -5.4 38.6 256 qam 24
3 3.15E+08 -5.2 38.9 256 qam 23
4 3.07E+08 -5.2 38.9 256 qam 22
5 2.91E+08 -4.9 38.6 256 qam 20
6 2.83E+08 -5 38.9 256 qam 19
7 2.75E+08 -5 38.9 256 qam 18
8 2.67E+08 -4.7 38.9 256 qam 17
9 2.59E+08 -4.7 40.3 256 qam 16
10 2.51E+08 -4.2 40.9 256 qam 15
11 2.43E+08 -4.4 40.3 256 qam 14
12 2.35E+08 -5 40.3 256 qam 13
13 2.27E+08 -4.5 38.9 256 qam 12
14 2.19E+08 -4 38.6 256 qam 11
15 2.11E+08 -4 40.3 256 qam 10
16 2.03E+08 -4 40.3 256 qam 9
17 1.95E+08 -3.7 40.3 256 qam 8
18 1.87E+08 -3.7 40.3 256 qam 7
19 1.79E+08 -3.5 40.9 256 qam 6
20 1.71E+08 -3.5 38.9 256 qam 5
21 1.63E+08 -3.5 38.9 256 qam 4
22 1.55E+08 -3.2 40.3 256 qam 3
23 1.47E+08 -2.4 40.3 256 qam 2
24 1.39E+08 -2.5 40.9 256 qam 1
 
I've had the same issue as you. I resolved mine by using the original virmin cable that came with my box. I'm using a 3 way splitter Konig 5-2400 MHz. Previously I tried other generic cables and had glitching galore! Hope this helps.
 
Yeah.. that's my final resort! But not sure my signal levels warrant the amplifier, did your signal levels look ok before you amplified?

I also notice when i download anything the glitching goes through the roof :(
Signal levels looked ok but I tried everything else and was at the end of my tether. Give it a try if it don't work you can always send it back
 
Yeah.. that's my final resort! But not sure my signal levels warrant the amplifier, did your signal levels look ok before you amplified?

I also notice when i download anything the glitching goes through the roof :(
Using mgcamd? Tried CCcam? May be logging issue

Sent from my HUAWEI VNS-L31 using Tapatalk
 
Back
Top