Liteon DG-16D4S - Unlocked Replacement PCB - PRE ORDER NOW

[bobby123]

PRE ORDER NOW !

XCONSOLES - Kick Ass Video Game Mods, Repair Kits and Accessories - XBOX 360

and

http://www.ck3.co.uk/liteon-dg-16d4s-unlocked-replacement_pcb.html
and at all other official Xecuter retailers

It cost a lot to research and manufacture this - it also cost a lot to source the parts.

We know its expensive and its not for everyone - but its a solution and you can choose to use it or not.
Do you have a faulty Liteon DG-16D4S DVD in your Xbox 360 ? Are you swapping your drive to another console and are unable to program your firmware due to write protection being enabled ?
Team Xecuter have done it again with this custom made replacement PCB. Fits all DG-16D4S drive versions and allows you to reprogram your firmware to the board and then to set it to write protect to secure against any accidental firmware corruption / erasing.

Fits all Liteon DG-16D4S Drives
Fully compatible with 9504, 0225 and 0401 fw revisions
Write Protect enable / disable feature
Simply swap out the old board with your new board and you are good to go !
Easily programmable using the X360USB PRO or compatible SATA.
Note: All replacement boards are shipped blank. You must program your consoles correct firmware version and drive key.

 

[axxxo]

Still a small amount of soldering required for this.
Power supply from original PCB will have to be cut or desoldered and soldered back to the replacement.
Alot easier than the PRO version i would imagine though

VERY expensive i have to say but a solution nonetheless £49.95 plus shipping!

If wires are not soldered back correctly i would imagine it would fry the PCB, a costly waste!

 

[axxxo]

Looks like I was wrong about the need for a small amount of soldering....

Unlocked Replacement PCB Update

From Team Xecuter...

Now that production is fully underway of the newly designed DG-16D4S PCB we have not only been able to reduce our production costs due to a larger than expected volume of wholesale orders, but we have also closed a deal to source a great amount of very difficult to find parts at a greatly reduced priced.

Our policy is always to be as competitive as possible, and these new savings will be reflected in the RRP and in the wholesale prices.

We should reiterate that this is not a simple copy of the DG-16D4S board, but a custom made version with a new chipset (and not just a single IC change), and it will be completely solderless – the install will simply be a cut and clip design.

Also note that if you are using a 9504 drive (if you are lucky enough to find a non-fake version) that the drive’s MT controller can be locked at ANY time via cdb commands. This is non reversible and is not a scare tactic, it is a fact. The custom DG-16D4S PCB has a manual write protect enable / disable switch so YOU are in control. You simply disable WP, Flash the drive, Enable WP and you are done.
We have tested the board on 9504, 0225 and 0401 consoles and they are working perfectly – all on Live with no problems whatsoever.
So, the first custom designed Liteon DG-16D4S Unlocked Replacement PCB now has an RRP of just $59.95.

The Pro Installers Kit which is the main IC and also the add-on circuit for write protect enable / disable etc is still available for an RRP of $19.99 and we are told by most major modders that they will be looking to charge around $30-$40 to install this for you if you can’t do it yourself.

We will post actual product images in the next week or so.

There are also several major new products to announce very soon – July will be a busy month indeed

Excellent news!

 

[axxxo]

As promised here are the images of the custom made DG-16D4S Unlocked PCB.

can't see where the cut and clip design is though for power? Looks to me like its soldered

​

 

[axxxo]

New Pictures Released

here is the very easy method for replacing the PCB and no soldering at all required (you can if you wish of course). Simply cut the 5 wires then strip 'n' screw. Simple.

The PCB's are now rolling off the lines and shipping to retailers begins on Monday morning from the factory - so give retailers a few days to receive stock and to ship out.

For the Pro Install kits, shipping began earlier this week and many retailers have already received stock (for USA customers, remember it is 4th July on Monday so most stores won't begin shipping until Tuesday)

As you can see it's not just the MT chip you have to replace but you also have a nice little QSB board to install. Again very easy - simply align and solder to the pads.

If your QSB looks different from the picture, don't worry there are different QSB versions to go with different MT replacement chips (make sure your QSB is used with the replacement MT chip that it is supplied with)

​