What's new
By:
Filters

WooshBuild USB not recognised on boot but is when attached after boot

D

dee pee

Newbie
Hi. H.2S running OpenATV 6.4 . Whooshbuild infinity 10.000

I put a NVMe m.2 drive in an enclosure to replace my existing USB SSD. If I plug in the enclosure then it gets detected. /var/log/messages shows

Jan 1 00:22:30 zgemmah2s user.info kernel: [ 2414.683000] usb 1-1: new high-speed USB device number 4 using ehci-brcm
Jan 1 00:22:30 zgemmah2s user.info kernel: [ 2414.807000] scsi host2: uas
Jan 1 00:22:30 zgemmah2s user.notice kernel: [ 2414.811000] scsi 2:0:0:0: Direct-Access SSK 0209 PQ: 0 ANSI: 6
Jan 1 00:22:30 zgemmah2s user.notice kernel: [ 2414.839000] sd 2:0:0:0: Attached scsi generic sg0 type 0
Jan 1 00:22:32 zgemmah2s user.notice kernel: [ 2416.818000] sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
Jan 1 00:22:32 zgemmah2s user.notice kernel: [ 2416.818000] sd 2:0:0:0: [sda] 4096-byte physical blocks
Jan 1 00:22:32 zgemmah2s user.notice kernel: [ 2416.819000] sd 2:0:0:0: [sda] Write Protect is off
Jan 1 00:22:32 zgemmah2s user.debug kernel: [ 2416.819000] sd 2:0:0:0: [sda] Mode Sense: 6b 00 00 08
Jan 1 00:22:32 zgemmah2s user.notice kernel: [ 2416.822000] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jan 1 00:22:32 zgemmah2s user.info kernel: [ 2416.835000] sda: sda1
Jan 1 00:22:32 zgemmah2s user.notice kernel: [ 2416.848000] sd 2:0:0:0: [sda] Attached SCSI disk
Jan 1 00:22:34 zgemmah2s daemon.notice ntfs-3g[6583]: Version 2017.3.23 integrated FUSE 27
Jan 1 00:22:34 zgemmah2s daemon.notice ntfs-3g[6583]: Mounted /dev/sda1 (Read-Write, label "New Volume", NTFS 3.1)
Jan 1 00:22:34 zgemmah2s daemon.notice ntfs-3g[6583]: Cmdline options:
Jan 1 00:22:34 zgemmah2s daemon.notice ntfs-3g[6583]: Mount options: allow_other,nonempty,relatime,fsname=/dev/sda1,blkdev,blksize=4096
Jan 1 00:22:34 zgemmah2s daemon.notice ntfs-3g[6583]: Ownership and permissions disabled, configuration type 1
Click to expand...

however if I restart the zgemma box, on boot the drive is not detected at all. No power goes to the drive. No mention or errors in the /var/log/messages file.

blkid shows no entry for it following a restart.


any ideas or should i concede defeat and keep using my old USB SSD that works fine?
 
As said wont work if box has not set it up and might be fat 32 which is not correct for recordings.
 
Its an NVMe m.2 even some PCs will not recognise them without being initialised. could also be driver problem.
 
just tried

MENU -> Setup -> System -> Storage Devices -> Initialisation. Initialised the drive.

Full Restart.

Checked Mount Manager - drive not shown.

checking /etc/fstab there is no entry for the drive. Do I manually have to add this or is there a way to automatically get the fstab entry?

thanks
 
You must log in or register to reply here.
Back
Top