Virmin saying noise on cable line

[nasifkhan]

removed attenuator and these are the results :

Downstream bonded channels
Channel Frequency (Hz) Power (dBmV) SNR (dB) Modulation Channel ID
1 299000000 2 36 256 qam 21
2 139000000 5.6 36 256 qam 1
3 147000000 4.8 36 256 qam 2
4 155000000 4.3 36 256 qam 3
5 163000000 4.4 36 256 qam 4
6 171000000 3.9 36 256 qam 5
7 179000000 3 36 256 qam 6
8 187000000 2.2 36 256 qam 7
9 195000000 2 35 256 qam 8
10 203000000 2.4 36 256 qam 9
11 211000000 1.5 36 256 qam 10
12 219000000 1 35 256 qam 11
13 227000000 1.2 35 256 qam 12
14 235000000 1.2 35 256 qam 13
15 243000000 0.5 35 256 qam 14
16 251000000 0.2 35 256 qam 15
17 259000000 0.7 36 256 qam 16
18 267000000 0.5 36 256 qam 17
19 275000000 0.5 36 256 qam 18
20 283000000 0.9 36 256 qam 19
21 291000000 1.2 36 256 qam 20
22 307000000 1.7 36 256 qam 22
23 315000000 2 36 256 qam 23
24 323000000 2.5 37 256 qam 24


Downstream bonded channels
Channel Locked Status RxMER (dB) Pre RS Errors Post RS Errors
1 Locked 36.3 5 0
2 Locked 36.3 2 0
3 Locked 36.3 20 0
4 Locked 36.3 4 0
5 Locked 36.6 5 0
6 Locked 36.3 10 0
7 Locked 36.1 7 0
8 Locked 35.7 3 0
9 Locked 35.7 11 0
10 Locked 36.3 7 0
11 Locked 36.3 6 0
12 Locked 33.9 1437 0
13 Locked 35 58 0
14 Locked 35.7 10 0
15 Locked 35.5 18 0
16 Locked 35.5 10 0
17 Locked 35.7 14 0
18 Locked 35.7 11 0
19 Locked 36.3 8 0
20 Locked 36.3 6 0
21 Locked 36.3 7 0
22 Locked 36.6 1 0
23 Locked 36.3 6 0
24 Locked 36.3 3 0

 

[nasifkhan]

the correct splitter to use as put on another post - http://www.techkings.org/threads/zgemma-h7c-no-vermin-channels.146377/page-2

thanks, ill order one

 

[pabloescaban]

are any of these tests with just the single incoming cable plugged into the router? - the splitter and everything else removed completely from the equation?
the test above without attenuator has done nothing for the SNR and the power levels look slightly better

 

[nasifkhan]

post 14 is single incoming cable into the router and everything else disconnected
post 17 is single incoming cable into splitter with 1 cable into router and 1 into box WITH attenuator
post 21 is single incoming cable into splitter with 1 cable into router and 1 into box WITHOUT attenuator

based on a previous post, it also seems i have the incorrect splitter. I should have technetix esx 5 - 1218 but i have labgear 5-24000

 

[gresco66]

i had a problem a couple of months ago. BT sports and a few of the film channels were scrambling all the time so i thought possibly something wrong with cable or router modem. engineer turned up (all of my gear disconected lol) he run a few tests and the problem was 5G had been turned off. so after getting it switched back on the problem was sorted.

 

[nasifkhan]

ive got 5g on.
im just waiting on the new splitter and will post results once it has been connected.

 

[pabloescaban]

ive got 5g on.
im just waiting on the new splitter and will post results once it has been connected.

The levels aren't good even without the splitter so doubt that will change things.
VM are going to need to adjust this for you, but they've already got it on file now that you are using hooky equipment.
remove the box and splitter and ring them back and tell them the internet is ususable and you want it either fixing or cancelling
Until they sort it out, the box won't work properly anyway

 

[nasifkhan]

I'll give them a call on Friday and see what they say/do.

 

[southsimon]

I'll give them a call on Friday and see what they say/do.[/QUOT

once you get the correct splitter you should be good to go. if not you can get a powered HDU. they defo work.

 

[nasifkhan]

with the correct splitter

Downstream bonded channels

Channel	Frequency (Hz)	Power (dBmV)	SNR (dB)	Modulation	Channel ID
1​	299000000​	3.2​	37​	256 qam​	21​
2​	139000000​	6​	37​	256 qam​	1​
3​	147000000​	5.4​	36​	256 qam​	2​
4​	155000000​	5.1​	37​	256 qam​	3​
5​	163000000​	4.8​	36​	256 qam​	4​
6​	171000000​	4.3​	36​	256 qam​	5​
7​	179000000​	3.9​	36​	256 qam​	6​
8​	187000000​	3.2​	36​	256 qam​	7​
9​	195000000​	2.7​	36​	256 qam​	8​
10​	203000000​	2.7​	36​	256 qam​	9​
11​	211000000​	2.2​	36​	256 qam​	10​
12​	219000000​	2.2​	36​	256 qam​	11​
13​	227000000​	2​	36​	256 qam​	12​
14​	235000000​	1.5​	36​	256 qam​	13​
15​	243000000​	1​	36​	256 qam​	14​
16​	251000000​	0.7​	36​	256 qam​	15​
17​	259000000​	0.9​	36​	256 qam​	16​
18​	267000000​	0.5​	36​	256 qam​	17​
19​	275000000​	1​	36​	256 qam​	18​
20​	283000000​	2​	36​	256 qam​	19​
21​	291000000​	2.7​	37​	256 qam​	20​
22​	307000000​	2.9​	37​	256 qam​	22​
23​	315000000​	3.2​	37​	256 qam​	23​
24​	323000000​	3.4​	37​	256 qam​	24​

Downstream bonded channels

Channel	Locked Status	RxMER (dB)	Pre RS Errors	Post RS Errors
1​	Locked​	37.3​	515​	8​
2​	Locked​	37.3​	1000​	410​
3​	Locked​	36.6​	1052​	395​
4​	Locked​	37.3​	882​	390​
5​	Locked​	36.3​	969​	417​
6​	Locked​	36.6​	941​	320​
7​	Locked​	36.6​	939​	215​
8​	Locked​	36.3​	1288​	208​
9​	Locked​	36.3​	1125​	207​
10​	Locked​	36.3​	1104​	148​
11​	Locked​	36.3​	1231​	207​
12​	Locked​	36.3​	7966​	157​
13​	Locked​	36.3​	3002​	120​
14​	Locked​	36.6​	1423​	139​
15​	Locked​	36.3​	2474​	85​
16​	Locked​	36.3​	1912​	57​
17​	Locked​	36.6​	1327​	54​
18​	Locked​	36.3​	1933​	31​
19​	Locked​	36.3​	1459​	22​
20​	Locked​	36.6​	890​	29​
21​	Locked​	37.3​	607​	25​
22​	Locked​	37.3​	524​	12​
23​	Locked​	37.3​	452​	0​
24​	Locked​	37.3​	612​	58​

 

[nasifkhan]

single incoming cable into splitter with 1 cable into router and 1 into box WITHOUT attenuator

 

[southsimon]

single incoming cable into splitter with 1 cable into router and 1 into box WITHOUT attenuator

so what was the result you all good now up and running?

 

[nasifkhan]

no idea. was working fine before i had the incorrect splitter and working just as good with the correct splitter.
was told that my signals were low with the incorrect splitter.
posted the above in the hope that someone would clarify whether they are ok now that i have the correct splitter.
Channels working really good with the current line provider.

 

[dave100]

Mate pablo has been away on his holidays but is back now so should be in here soon to help you
And what a great help he is

 

[dave100]

@moshibeth
I was not being sarcastic, he genuinely is a great help on this forum

Not like you

 

[moshibeth]

@moshibeth
I was not being sarcastic, he genuinely is a great help on this forum

Not like you

He is i know that tricky dave

 

[dave100]

& what about you?
Are you just the ass

 

[dave100]

I see you like to pick on people on the forum that are liked, this is out of order lamblamb is a great member of this community

It may be best to stop this before people start to hate you or is it to late

 

[pabloescaban]

not sure what's been posted here as it looks like some posts have been deleted/moderated.
I told OP to use a decent quality splitter and he now gets decent picture, so everything good.
recently another 'aquaintance' is struggling to get a signal to his H9T so I've told him to get a HDU as it appears he's using splitter after splitter to get the VM cable from one room to another, obviously long lengths of cables are involved and he's using multiple boxes as well as the router, but i'm not 100% convinced the H9T is working as it should - has anyone had any dealings with these boxes? - i've flashed and set up other H9 boxes (via teamviewer) and not been impressed with any of them TBH but this is first H9T i've dealt with and it seems like a POS to me...he has kryptview boxes and they also don't work but that could just be due to the fact they are crap but he has VM BB and that works fine. H9T will scan in ABM and finds channels, surely this means it's connected to VM?
Network test is fine, channel 4 and 5 work ok (didn't try bbc as these are now HD) but using oscam and CCcam softcams do nothing.
Next step is take it to mate's house to see if it will clear but open to suggestions