No I haven't as I've been using XE for a very long time and got so used to it I'm a bit loss without it but I guess it's coming to it's end now. Do I have to reflash my box with willowbuild or just install it like XE?Have you guys tried box and willobuild to see if have same issues
Cool, let me know if you find any 👍🏻I think it's the similar issue. And I was thinking of downgrade back to version 6.4 but even with that I was unable to pull EPG hence for looking at my options
Willobuild runs on Vix, if openatv is the cause of the problems, then this should be a solution.No I haven't as I've been using XE for a very long time and got so used to it I'm a bit loss without it but I guess it's coming to it's end now. Do I have to reflash my box with willowbuild or just install it like XE?
Willobuild uses vix you would need that firmwareNo I haven't as I've been using XE for a very long time and got so used to it I'm a bit loss without it but I guess it's coming to it's end now. Do I have to reflash my box with willowbuild or just install it like XE?
Yeah and he said it's to do with XE not updating and noncompatible with OpenATVWillobuild runs on Vix, if openatv is the cause of the problems, then this should be a solution.
I'm assuming both of you have asked your provider about EPG problems?
Will have to do my research on how to flash my box with vix 1st and then Rey willobuildWillobuild uses vix you would need that firmware
Will keep you update once I found what work for me!Cool, let me know if you find any 👍🏻
All the info is on his setup page 10 minute job to flash it just make sure you have a usb mounted in the box ready.Will have to do my research on how to flash my box with vix 1st and then Rey willobuild
Thank you👍🏾All the info is on his setup page 10 minute job to flash it just make sure you have a usb mounted in the box ready.
WilloBuild OpenViX 6.3 Series
Hi, so I was following @Willo3092 instructions on how to install openvix and willobuild on my zgemma h9.2s. I've prep the box as instructed and media/had formated to EXT4 too but when I paste the code provided onto the terminal. It keeps saying "No space left on device ". Any idea please?All the info is on his setup page 10 minute job to flash it just make sure you have a usb mounted in the box ready.
WilloBuild OpenViX 6.3 Series
Did you initialise the usb first?Hi, so I was following @Willo3092 instructions on how to install openvix and willobuild on my zgemma h9.2s. I've prep the box as instructed and media/had formated to EXT4 too but when I paste the code provided onto the terminal. It keeps saying "No space left on device ". Any idea please?
Yes I did several timesDid you initialise the usb first?
If it's reporting there's not enough room, it's not seeing the usb and it's trying to use internal flash.Yes I did several times
I'm just reflashing the box again now with ATV and see if that works. But the USB was mounted cuz I checked but I'll give that ago after reflash box again and if it doesn't work then back to drawing board 😁If it's reporting there's not enough room, it's not seeing the usb and it's trying to use internal flash.
I only use ATV which mounts the usb automatically once it's initialised, I think on Vix you have to manually mount the usb after initialisation, did you do this?
What make / size usb?
Crusade my go to. I've been using the make for along time. Anyway the reflash seem to have sort it out and now downloading. So fingers crossedWhat make usb is it cheap ones are no good a genuine sandisk works great on zgemma 16GB or less
Damn it stopped saying error and now the box is rebooting.....aaaaaahhhhh🫠Crusade my go to. I've been using the make for along time. Anyway the reflash seem to have sort it out and now downloading. So fingers crossed