What's new
By:

zgemma h2s

R

raymon

Newbie
any help would be appreciated box stuck on boot red light on box doing nothing at all tried downloads wont go in to the box at the front and the rear just stays on boot any ideas ?
 
Use a different power supply
This is very common and a new psu works 99% of the time
When it powers up you can then flash it
 
What ampage were the ones you tried?
Should be at least as powerful as the original, preferably higher
Try a higher amp psu and it will boot up
 
pabloescaban said:
What ampage were the ones you tried?
Should be at least as powerful as the original, preferably higher
Try a higher amp psu and it will boot up
Click to expand...
Hi there, I've the exact same problem with zeggy h2h had a crap little 3.99 12v 0.5amp number and swapped it for another one similar 3000ma 12v. At first red light and "boot" was on the lcd but since swapping the psu it's just "boot" that's showing on lcd now. I've got most of the files on pc but haven't got enigma as I can't find it. Do i need the box to turn on or can I flash it while it's in boot? I know that's a stupid question and I'll probs get roasted for it lol. But wet behind the ears here I'm used to droid boxes. Any help or advice muchas gracias
 
You need to locate your box ip address if possible or go on here openATV Nightly Downloads the latest zip file extract zip file open zgemma folder if there's a file that, says noforce rename to force put the extracted zgemma folder onto formatted fat32 USB stick completely power the box off by white button put the USB with the zgemma file into rear USB port power box on then should flash your box for then once flashed get your box ip address and go down to all builds and select an image to install and follow there install guide
 
Last edited:
bazcfc1 said:
You need to locate your box ip address if possible or go on here openATV Nightly Downloads download the latest zip file extract zip file open zgemma folder if there's a file that, says noforce rename to force put the extracted zgemma folder onto formatted fat32 USB stick completely power the box off by white button put the USB with the zgemma file into rear USB port power box on then should flash your box for then once flashed get your box ip address and go down to all builds and select an image to install and follow there install guide
Click to expand...
Right baz shweet advice am going to format USB and do this just now. Proud of ya
 
bazcfc1 said:
You need to locate your box ip address if possible or go on here openATV Nightly Downloads download the latest zip file extract zip file open zgemma folder if there's a file that, says noforce rename to force put the extracted zgemma folder onto formatted fat32 USB stick completely power the box off by white button put the USB with the zgemma file into rear USB port power box on then should flash your box for then once flashed get your box ip address and go down to all builds and select an image to install and follow there install guide
Click to expand...
Is that openatv 6.0?
My fone is playing up, can't find 6.4 for h2h
 
having the same issue as above. Tried a different power supply (works on my other h2h) but this did not work.
Tried re-flashing ... renamed noforce to force and the display shows flsh, after a few minutes it goes to boot but remains stuck with red light.

tried removing the usb after flash completes and restarting the box, but having no luck. Any help would be useful, thanks.
 
You must log in or register to reply here.

Similar threads

Blingking
Black screen even on boot up H7
Replies
8
Views
65
Blingking
Blingking
M
zgemma h11s
Replies
7
Views
465
cactikid
cactikid
O
Zero SNR - Zgemma H2S
Replies
4
Views
286
Abu Baniaz
A
taffusmarideus
Zgemma h2s advice needed
Replies
15
Views
1K
frundlemud
frundlemud
B
Zgemma h17 combo freeze
Replies
0
Views
15
bee9791
B
Back
Top