What's new
By:

Zgemma star H1 Question.

B

bob14

Member
I have a old Zgemma star H1
My Question is would the Zgemma star H1 work using motorized set up and Oscam.
I have flashed openpli-9.1 image downloaded with Oscam softcam.
I have not been able to get the Zgemma to move or have signal from the motor.
I have tried setting up with Usals with settings below.

Configuration Mode to Simple
Set the Mode to Positioner
Longitude and Latitude.

I know the motor works as when using a master slave lnb switch to viark sat k4 and Gtmedia v8 uhd all's ok.
 
bob14 said:
I have a old Zgemma star H1
My Question is would the Zgemma star H1 work using motorized set up and Oscam.
I have flashed openpli-9.1 image downloaded with Oscam softcam.
I have not been able to get the Zgemma to move or have signal from the motor.
I have tried setting up with Usals with settings below.

Configuration Mode to Simple
Set the Mode to Positioner
Longitude and Latitude.

I know the motor works as when using a master slave lnb switch to viark sat k4 and Gtmedia v8 uhd all's ok.
Click to expand...
Try removing any slave master switches direct connection to the motor to test.
 
I connected direct to the motorized satellite dish.

I flashed a new image open at 7.6 put in Usals, still does not move dish.
The dish is parked at 28.2, the Zgemma star H1 shows no signal.

All ok on Gtmedia V8
 
bob14 said:
I connected direct to the motorized satellite dish.

I flashed a new image open at 7.6 put in Usals, still does not move dish.
The dish is parked at 28.2, the Zgemma star H1 shows no signal.

All ok on Gtmedia V8
Click to expand...
Have you tried using a channel list to select the channels from to move the dish..
 
I downloaded a Vhannibal motor list from the plugin menu put on bbc from the list and no signal
 
Tomorrow I will set up a temporary dish,
Set tuner configuration to single setting to see if I get a signal
 
I was not able to try a temporary dish ( bad weather), so I flashed a new image openPLI - 9.1 downloaded an Oscam softcam from plugin menu converted clines into Oscam server file. Then downloaded motor channel list from plugin menu. I then set tuner configuration as above.
Connected to a Technomate motor
( motor on table not connected to a dish )

Motor moved to different locations when channels choosen. I moved motor from channel list from 0.8w to 52e, then to 7 w back to 0.8w by picking channels from above satellite.

I then connected the Zgemma star H1 back to my motorized set, again no signal and no movement. The motorized set up is on a Stab hh 100 motor. ( The stab setup works with both viark and Gtmedia boxes either straight connection or through a LNB priority switch)
 
I set up a temporary motorized dish set up with Technomate motor and my Zgemma star H1.

Firstly I set the dish and motor with a Gtmedia to 0.8w. and checked against other satellites.

Then connected up the Zgemma star H1 to the motor, worked fine moving motor with channels clearing.

Not sure why when using Usals settings the Zgemma star H1 will only move the motor and tune into channels on the Technomate motor and not the stab.

Gtmedia and viark work with both motors.
 
Please does anyone know the reason why the Zgemma star H1 will not move or tune into a Stab HH 100 motor, but will move and tune into a Technomate motor.

I have tested this using all the same cabling with Viark sat k4 and Gtmedia v8 uhd which move and tune into on both motors.
The Zgemma star H1 only works on the Technomate.

My Question is does any know the reason or how to get the Zgemma star H1 to use the Stab motor.
 
You must log in or register to reply here.
Back
Top