Wooshbuild 5 on H2H All good

ste

TK Veteran
... but as you wanted Wooshbuild which is based on ATV, I suggested ATV first but the choice is yours :)
 

Trilliano

Registered
Ive tried dsayers and bioheads images and must say they are PERFECT for the H2H. But I wanted to try Wooshbuild 5 see if it was ok?

So I Installed Wooshbuild 5.
Then Menu - Setup - Service Searching - Tuner Configuration - highlight tuner B - Ok - Then change Net ID to your area - then Green button to save.
Exit back to tv. Green button - Red button (remove plugins) - extensions - highlight autobouquets and press ok - (MESSAGE READS Do you want to remove the plugin "extensions-autobouquets"?) Highlight YES and press OK - exit back to tv - ****NOW THE IMPORTANT PART**** Menu - Standby/Restart - RESTART GUI ****It must be (RESTART GUI) and not just restart!!!!!! (If you press just restart Autobouqets E2 will still be there!!!!!!!!)
Green button - Green button (download plugins) - System Plugins - AutobouqetMaker (ABM) - Download then restart box - Menu - Standby/Restart - RESTART GUI.
Menu - Setup - Service Searching - Autobouqemaker - Configure - change setup mode to Expert - Sheduled scan (turn to ON) - change Time of Scan to Whatever time ( I used 5am) - Press Exit - Providers - make sure Virgin U.K. is (ON) - Virgin Swap Channels is (ON) and your Net Id for your area is there . - Press Exit - Start Scan ( Will now Scan for Channels).
Once finished then Menu - Setup - EPG - Settings - Enable Virgin epg ( change to YES the press GREEN button to Save.
Press Exit back to Setup - CrossEpg -Configure - Schedule Download ( change to wherever ( I used (5.15am).
Press Exit - XMLTV PROVIDERS - Sroll down to bottom and choose RYTEC Virgin U.K. XMLTV then press GREEN to enable - Press Yellow to Download - ( once finished make sure there's a tick on Ryteck virgin uk).
Press Exit.
Providers Start Order - Highlight Rytec Virgin and press GREEN button to move up so RYTEC virgin is at the top!
Press Exit - Download Now - Now will Download the Epg. where do i ger virgin skin?

Then I FTP into box using Filezilla and transferred my newcamd.list file into usr/keys.
Then Blue Button - Press Down Button once - Press Right Button once - (softcam Panel "control your softcams") - press OK - Highlight Select Cam 1 - Press Right Button Twice till it says mgcamd_1.38rl - press GREEN button this will restart cam. - now exit back to tv.

I then downloaded the VirginHD skin and Installed it aswell.
All Virgin Channels working fine including HD and Epg working g a treat!
If I've missed anything out or done something you thinks wrong guys let me know.

Things to NOTE:
1. I left TUNER A as it was.
2. Always check your using the correct NET ID.
3. I was using a N-line in Mgcamd. (But obviously you can use c:line CCCam).
4. This guide is for Cable ONLY!! But you can run Sky with this also.
5. Big thanks to Wooshman (Wooshbuild is a great build mate)


Might help someone if they fancy using Wooshbuild eh!
 

ste

TK Veteran
Thanks for this.

However I keep getting an error on all the channels after I have done an Autotune.

The error is
"Getting Event Info Failed
invalid null reference in method...."

Does anyone have any ideas. I have re-tuned 6 times now. Even the FTA channels have it.

Thanks
And you've got the V*rgin cable plugged into the RF IN slot in the back of the receiver?

Are you using Autobouquetsmaker to search for your channels?
 

Gazzeg

Registered
Yes got the cable in the right tuner as had it working earlier on Andy AVT image.

I have used the Tuner autotune to get the channels. I thought you had to tune the channels first then run Autobouquetsmaker after to organise the channel listings.

I know the ZGemma H1 is an older box but I was hoping to get something speedier on the interface and have the V/M looking skin.
 

ste

TK Veteran
No, you either use one or the other - Autobouquetsmaker is the ones you should be using.

I'd stick to a fresh image on that box and just install the bare minimum.
 

Gazzeg

Registered
Hi,

Id love to just have the Stock ATV or VIX (Which ever is faster and only load on the essentials. However, there is no clear tutorial of whats needed for basics. Id assume the following:

Softkey
Autobouquette (however its spelt)
but then totally unsure.

I'd be happy to build this and share with others out there on here is anyone else could help or PM me help so I could then backup the image and share a basic one.

Regards,
 

Biohead

Registered
That what I did with my image - it's nothing more than whats needed to watch VM and also have a working EPG.

I guess the only thing with mine is it doesn't use the stock ATV skin.
 

alan michie

Registered
Ive tried dsayers and bioheads images and must say they are PERFECT for the H2H. But I wanted to try Wooshbuild 5 see if it was ok?

So I Installed Wooshbuild 5.
Then Menu - Setup - Service Searching - Tuner Configuration - highlight tuner B - Ok - Then change Net ID to your area - then Green button to save.
Exit back to tv. Green button - Red button (remove plugins) - extensions - highlight autobouquets and press ok - (MESSAGE READS Do you want to remove the plugin "extensions-autobouquets"?) Highlight YES and press OK - exit back to tv - ****NOW THE IMPORTANT PART**** Menu - Standby/Restart - RESTART GUI ****It must be (RESTART GUI) and not just restart!!!!!! (If you press just restart Autobouqets E2 will still be there!!!!!!!!)
Green button - Green button (download plugins) - System Plugins - AutobouqetMaker (ABM) - Download then restart box - Menu - Standby/Restart - RESTART GUI.
Menu - Setup - Service Searching - Autobouqemaker - Configure - change setup mode to Expert - Sheduled scan (turn to ON) - change Time of Scan to Whatever time ( I used 5am) - Press Exit - Providers - make sure Virgin U.K. is (ON) - Virgin Swap Channels is (ON) and your Net Id for your area is there . - Press Exit - Start Scan ( Will now Scan for Channels).
Once finished then Menu - Setup - EPG - Settings - Enable Virgin epg ( change to YES the press GREEN button to Save.
Press Exit back to Setup - CrossEpg -Configure - Schedule Download ( change to wherever ( I used (5.15am).
Press Exit - XMLTV PROVIDERS - Sroll down to bottom and choose RYTEC Virgin U.K. XMLTV then press GREEN to enable - Press Yellow to Download - ( once finished make sure there's a tick on Ryteck virgin uk).
Press Exit.
Providers Start Order - Highlight Rytec Virgin and press GREEN button to move up so RYTEC virgin is at the top!
Press Exit - Download Now - Now will Download the Epg.

Then I FTP into box using Filezilla and transferred my newcamd.list file into usr/keys.
Then Blue Button - Press Down Button once - Press Right Button once - (softcam Panel "control your softcams") - press OK - Highlight Select Cam 1 - Press Right Button Twice till it says mgcamd_1.38rl - press GREEN button this will restart cam. - now exit back to tv.

I then downloaded the VirginHD skin and Installed it aswell.
All Virgin Channels working fine including HD and Epg working g a treat!
If I've missed anything out or done something you thinks wrong guys let me know.

Things to NOTE:
1. I left TUNER A as it was.
2. Always check your using the correct NET ID.
3. I was using a N-line in Mgcamd. (But obviously you can use c:line CCCam).
4. This guide is for Cable ONLY!! But you can run Sky with this also.
5. Big thanks to Wooshman (Wooshbuild is a great build mate)


Might help someone if they fancy using Wooshbuild eh!
hi thanks for the install info working perfect
 

carling1968

Registered
Unable to find RYTEC Virgin U.K in XMLTV PROVIDERS on Wooshbuild 7,
I've tried updating the RYTEC PROVIDERS but its still not there.
 

Supasparx

Registered
Ive tried dsayers and bioheads images and must say they are PERFECT for the H2H. But I wanted to try Wooshbuild 5 see if it was ok?

So I Installed Wooshbuild 5.
Then Menu - Setup - Service Searching - Tuner Configuration - highlight tuner B - Ok - Then change Net ID to your area - then Green button to save.
Exit back to tv. Green button - Red button (remove plugins) - extensions - highlight autobouquets and press ok - (MESSAGE READS Do you want to remove the plugin "extensions-autobouquets"?) Highlight YES and press OK - exit back to tv - ****NOW THE IMPORTANT PART**** Menu - Standby/Restart - RESTART GUI ****It must be (RESTART GUI) and not just restart!!!!!! (If you press just restart Autobouqets E2 will still be there!!!!!!!!)
Green button - Green button (download plugins) - System Plugins - AutobouqetMaker (ABM) - Download then restart box - Menu - Standby/Restart - RESTART GUI.
Menu - Setup - Service Searching - Autobouqemaker - Configure - change setup mode to Expert - Sheduled scan (turn to ON) - change Time of Scan to Whatever time ( I used 5am) - Press Exit - Providers - make sure Virgin U.K. is (ON) - Virgin Swap Channels is (ON) and your Net Id for your area is there . - Press Exit - Start Scan ( Will now Scan for Channels).
Once finished then Menu - Setup - EPG - Settings - Enable Virgin epg ( change to YES the press GREEN button to Save.
Press Exit back to Setup - CrossEpg -Configure - Schedule Download ( change to wherever ( I used (5.15am).
Press Exit - XMLTV PROVIDERS - Sroll down to bottom and choose RYTEC Virgin U.K. XMLTV then press GREEN to enable - Press Yellow to Download - ( once finished make sure there's a tick on Ryteck virgin uk).
Press Exit.
Providers Start Order - Highlight Rytec Virgin and press GREEN button to move up so RYTEC virgin is at the top!
Press Exit - Download Now - Now will Download the Epg.

Then I FTP into box using Filezilla and transferred my newcamd.list file into usr/keys.
Then Blue Button - Press Down Button once - Press Right Button once - (softcam Panel "control your softcams") - press OK - Highlight Select Cam 1 - Press Right Button Twice till it says mgcamd_1.38rl - press GREEN button this will restart cam. - now exit back to tv.

I then downloaded the VirginHD skin and Installed it aswell.
All Virgin Channels working fine including HD and Epg working g a treat!
If I've missed anything out or done something you thinks wrong guys let me know.

Things to NOTE:
1. I left TUNER A as it was.
2. Always check your using the correct NET ID.
3. I was using a N-line in Mgcamd. (But obviously you can use c:line CCCam).
4. This guide is for Cable ONLY!! But you can run Sky with this also.
5. Big thanks to Wooshman (Wooshbuild is a great build mate)


Might help someone if they fancy using Wooshbuild eh!
Hi, I wonder if anyone is willing to help?

So the story goes that I have a Zgemma Star H2 that was installed with Openvix and running Virgin Media package via cable for the last 18months.

I've just bought a new 12 month sub off another provider who suggested that I change to Wooshbuild V5.

I've installed Basebuild, flashed to wooshbuild and carried out all the steps as above with regards to autobouquetsmaker etc.

Incidentally I hadn't added my line to the USB when flasjing the box.

The issue I have now is that I don't know where exactly to enter my line? I don't have newcamd.list showing in usr/keys or anywhere else that I can see.

I have CCcam 2.3.0 showing in the Softcam Panel butr can't find it in Dreamexplorer in order to edit the line.


I've tried to FTP an old CCcam.cfg file that I had but that doesn't seem to be working.

Has anyone got any advice?

Basically I am a relative novice when it comes to tech etc. but I'm good at following instructions, especially if put down in an idiotproof format lol...

TIA for any assistance offered....
 

ste

TK Veteran
Hi, I wonder if anyone is willing to help?

So the story goes that I have a Zgemma Star H2 that was installed with Openvix and running Virgin Media package via cable for the last 18months.

I've just bought a new 12 month sub off another provider who suggested that I change to Wooshbuild V5.

I've installed Basebuild, flashed to wooshbuild and carried out all the steps as above with regards to autobouquetsmaker etc.

Incidentally I hadn't added my line to the USB when flasjing the box.

The issue I have now is that I don't know where exactly to enter my line? I don't have newcamd.list showing in usr/keys or anywhere else that I can see.

I have CCcam 2.3.0 showing in the Softcam Panel butr can't find it in Dreamexplorer in order to edit the line.


I've tried to FTP an old CCcam.cfg file that I had but that doesn't seem to be working.

Has anyone got any advice?

Basically I am a relative novice when it comes to tech etc. but I'm good at following instructions, especially if put down in an idiotproof format lol...

TIA for any assistance offered....
The new 12 months sub you bought - this needs to go into the ROOT > USR > KEYS folder ... you can either ask your line provider to send you the line details over as a file ready to put into the KEYS folder or you can make the file yourself - either CCCam.cfg or newcamd.list ... you create this with notepad on a computer and be sure you change file type to "all" before hitting save.
 
Top