WooshBuild Wooshbuild Install 2022

What box have you got and what are you watching, sat or IPTV?
Has it just started happening or is it from a fresh install?
Latest Wooshbuild is mid 2018.
I have a Octagon SF8008 and this has just started over the last week or two. I'm running iptv and have been for quite some time, this would happen on every channel, could it be a provider issue.
 

wheelo

Admin
Staff member
TK Supporter
Baffles me why people still use it to be honest.
Would it surprise you to know that I still use it with absolutely no problems?
Would it surprise you to know that I have it on a H2S AND H52TC with no problems?
I have a Octagon SF8008 and this has just started over the last week or two. I'm running iptv and have been for quite some time, this would happen on every channel, could it be a provider issue.
Sometimes the version of open ATV changes, or you do a software update, or add a plugin, or delete a plugin and something gets corrupted. If it's been on a while with no problems, I would just reflash, it takes maybe 7 minutes.

If the circle is a regular thing, regardless of build ~ for me, the solution is to just reflash as it's so simple nowadays.
 

pabloescaban

VIP Member
TK Supporter
Im on mobile data at the moment and cannot open your photo but a spinning circle usually means something is running in the background.
Openwebif and click Terminal, type opkg update and click enter.
That may do the trick
 

urie

TK Veteran
TK Supporter
You can still get the spinning circle even on fresh install even with machine with more than enough memory , could be even changing channel on iptv source stream not available it should go away eventually but sometimes can lock up the stb even worse on older stb's even with swap enabled at the end of the day it is just a busy pointer.
 

Willo3092

VIP Member
I have a Octagon SF8008 and this has just started over the last week or two. I'm running iptv and have been for quite some time, this would happen on every channel, could it be a provider issue.

My advice would be to flash a clean image on one of the free multiboot partitions if you have a spare one.
That will eliminate any problems with your current image and build.
 

suttsy

Newbie
Hi Folks,
I started fooling around with my Vu Solo2 and flashed a few different images, however I had to return to wooshbuild as It suits my needs.
My problem is I cant connect through telnet, I always though that my IP address + Root + Dreambox + Port was enough to communicate with the receiver.
However, the password appears to be wrong as below:
Command: USER root
Response: 331 Please specify the password.
Command: PASS ********
Response: 530 Login incorrect.
Error: Critical error: Could not connect to server

Can anyone advise on this issue or may have witnessed same.
I'd appreciate any help on this.

Regards
Suttsy
 

rapidwrinkly

TK Veteran
TK Supporter
Hi Folks,
I started fooling around with my Vu Solo2 and flashed a few different images, however I had to return to wooshbuild as It suits my needs.
My problem is I cant connect through telnet, I always though that my IP address + Root + Dreambox + Port was enough to communicate with the receiver.
However, the password appears to be wrong as below:
Command: USER root
Response: 331 Please specify the password.
Command: PASS ********
Response: 530 Login incorrect.
Error: Critical error: Could not connect to server

Can anyone advise on this issue or may have witnessed same.
I'd appreciate any help on this.

Regards
Suttsy
You need to set up a password in network
 

pabloescaban

VIP Member
TK Supporter
Hi Folks,
I started fooling around with my Vu Solo2 and flashed a few different images, however I had to return to wooshbuild as It suits my needs.
My problem is I cant connect through telnet, I always though that my IP address + Root + Dreambox + Port was enough to communicate with the receiver.
However, the password appears to be wrong as below:
Command: USER root
Response: 331 Please specify the password.
Command: PASS ********
Response: 530 Login incorrect.
Error: Critical error: Could not connect to server

Can anyone advise on this issue or may have witnessed same.
I'd appreciate any help on this.

Regards
Suttsy
You have to set up a password on the box using the remote first.
Menu setup system network password setup
 
Top