BT Sport

[pabloescaban]

yeah, got it earlier. not using vix, open atv

After dropping it in tmp folder
Press portal button
8 software management
Ipkg install

 

[moshibeth]

After dropping it in tmp folder
Press portal button
8 software management
Ipkg install

atv lover you

 

[grahamer67]

Got that bit done ok earlier, but its the next bit that I got stuck on

 

[pabloescaban]

Got that bit done ok earlier, but its the next bit that I got stuck on

Once it's installed, the softcam you want will be in the softcam feeds
Green
Green
Softcams

 

[dazbon]

To all of those that have been working hard in the background, you know who you are, just wanted to say thank you

 

[linesman66]

To many big brother's watching

 

[Peter1984]

Average ecm time (200 ms)
On all channels

When using oscam are you using two different lines or just one?

 

[edmoses]

Where can I download oscam emu 11667 ipk from please?

mine is showing 1.20+git1926 currently

 

[urie]

Where can I download oscam emu 11667 ipk from please?

mine is showing 1.20+git1926 currently

if you go to oscam setup \info show log it will give you correct oscan version details

 

[edmoses]

if you go to oscam setup \info show log it will give you correct oscan version details

Ok so I've pressed red button > softcam-setup and showing oscam-emu

clicked on blue button (info) then show log and I get error: oscam webif disabled

if i try go to port :83 on my box ip nothing loads either?

oscam stable is showing 1,20_svn build r11581 however

 

[moshibeth]

Ok so I've pressed red button > softcam-setup and showing oscam-emu

clicked on blue button (info) then show log and I get error: oscam webif disabled

if i try go to port :83 on my box ip nothing loads either?

oscam stable is showing 1,20_svn build r11581 however

Use the latest version of oscam and should be listed in feeds

 

[edmoses]

Use the latest version of oscam and should be listed in feeds

I see the following in download softcams

- Oscam-emu 1.20+git1926 (IPv4 only)
- Oscam-trunk 1.20+svn11668 (IPv6/IPv4 Dual-Stack Support)
- Oscam-trunk 1.20+svn11668 (IPv4 only)

Which one do i need please?

 

[edmoses]

Managed to get Oscam Version 1.20_svn build r11667-798 installed now thanks to @linesman66

How do I now add my existing mgcamd line into oscam please?

 

[pabloescaban]

Managed to get Oscam Version 1.20_svn build r11667-798 installed now thanks to @linesman66

How do I now add my existing mgcamd line into oscam please?

Don't tell him Pike!

 

[Northern Monkey]

Reading this thread made me realise my Gigablue ultra ue hadn’t updated since June and no updates available on the receiver.
So downloaded the latest openvix image (5.4.001) and flashed.
The latest Oscam version in the download section on the receiver is “Oscam-pcscd-latest (1.20+svn11650-r0)”
Any ideas why this is?
I see people mentioning a different latest version.
no updates on the receiver.
thanks

 

[Abu Baniaz]

The oscam on the "feeds" only gets updated when an image build is run.

Openvix 5.4 001 was run over 3 weeks ago. OpenATV run almost daily builds.

 

[Northern Monkey]

The oscam on the "feeds" only gets updated when an image build is run.

Openvix 5.4 001 was run over 3 weeks ago. OpenATV run almost daily builds.

No problem just thought I’d check.
thanks.

 

[Peter1984]

Managed to get Oscam Version 1.20_svn build r11667-798 installed now thanks to @linesman66

How do I now add my existing mgcamd line into oscam please?

Hi mate any chance you could point me in the right direction as I can't find this version of oscam either. Thanks

 

[Peter1984]

yeah, got it earlier. not using vix, open atv

Hi mate where can I download the ipk file for this version of oscam I can't seem to find it anywhere. Thanks

 

[grahamer67]

Didnt work for me, none of my lines would open when I tried them in it.