What's new
By:
Filters

WooshBuild Wooshbuild Infinity Support Thread

Status
Not open for further replies.
Got it working..

Just thought I'd put what errors I made to help others.

When I went to input line in usr/keys all that was in there was oscam_atv_emu mg_cfg and cccam_cfg

Where I went wrong was went into mg_cfg first and deleted all the info in there because i thought my line went in there stupidly.

Only once I put mg_cfg back to how it was and copied newcamd.list in did it work.

Thanks for the help guys...
 
chris_mcfc said:
Hi.. Thanks. But my supplier doesn't support cccam and I'd rather not use it myself really. Also I have another box using the line as multi room upstairs.

I'm using mgcamd fine on another box and it's woosh on 6.2.. I managed to save settings from another build of atv though so I didn't do a fresh install on that one..

Seems strange this as the softcam is there and running and I have placed the file in the right place
Click to expand...

Use what files you may need from my keys folder ;)

https://mega.nz/#!aUcWBArY!ZfDsvu6jifNG38BG3p_vz-YZd5rav8U4HhW_n5Z3FNo
 
epgimp.jpg
Scrads14 said:
Not long probs less then 5mins and only gets about 29channels
Click to expand...

you've got the wrong settings in epg importer
open epgimporter>press blue>choose Rytec UK sat/virgin press ok
make sure theres green ticks in the six categories that open up underneath.
press green to save then press yellow
 
Last edited:
Does anyone know how I'd get to the video setup that you can alter the screen size with? I did this during setup but I'm not happy with it.

Also, not really important but I'd like to change the red vm skin I'm using to the purple vm one that you can choose on setup. You get the option when setting up but I can't find it now. Would I need to ftp one to the box?

Cheers guys...
 
chris_mcfc said:
Does anyone know how I'd get to the video setup that you can alter the screen size with? I did this during setup but I'm not happy with it.

Also, not really important but I'd like to change the red vm skin I'm using to the purple vm one that you can choose on setup. You get the option when setting up but I can't find it now. Would I need to ftp one to the box?

Cheers guys...
Click to expand...
for your screen menu/setup/usage&gui/extended gui/osd position. and for your skin green button/green again for downloadable plugins/skins and you will find the purple one in there download it then exit out then go green/ wbconfig/ change skin and change it to purple one
 
gray1313 said:
for your screen menu/setup/usage&gui/extended gui/osd position. and for your skin green button/green again for downloadable plugins/skins and you will find the purple one in there download it then exit out then go green/ wbconfig/ change skin and change it to purple one
Click to expand...


Superb.. All sorted thank you!
 
Hi Just installed infinity but unsure if my VPN is working as the IP address stays the same no matter which country I run it through, any advice, please.
 
After having spent a rather long time setting up my new H2s on 6.2 I think I should have gone the Wooshbuild route. Two questions please. Can I go straight into a Webif terminal installation or do I need to do a factory reset or similar first? I am in France so another question is do I need to set the zgemma system time to GMT?
 
Baldlygo said:
After having spent a rather long time setting up my new H2s on 6.2 I think I should have gone the Wooshbuild route. Two questions please. Can I go straight into a Webif terminal installation or do I need to do a factory reset or similar first? I am in France so another question is do I need to set the zgemma system time to GMT?
Click to expand...
You need to re flash open atv 6.2, then when you get to the network wizard, follow the instructions on page one of the infinity thread.
 
Thanks grahamer - I made a mistake above cause my h2s is on atv 6.1 out of the box. Therefore I have not had to do any flashes and am a newbie to sat boxes - sorry :(
 
Status
Not open for further replies.
Back
Top