What's new

PLEASE HELP step by step help needed for a complete zgemma h.2s novice.

sleep well Wooshman
thanks os much for your help & patience x

---------- Post Merged at 01:05 AM ----------

the 'line installer' file in the put your line on box folder

where is the line installer???? my laptop or my tv box????

---------- Post Merged at 01:06 AM ----------

the 'line installer' file in the put your line on box folder


where is the line installer???? my laptop or my tv box????
 
laptop. running the file basically put the line on your box. then you do what woosh said in his previous post and activate the line and robs your dad brother
 
Screenshot_1.png
laptop. running the file basically put the line on your box. then you do what woosh said in his previous post and activate the line and robs your dad brother


is that what you mean??????

16300d1456262664t-please-help-step-step-help-needed-complete-zgemma-h-2s-novice-screenshot_1.png
 
Last edited:
Yeah. Once you've done that follow what Woosh put in post #53

---------- Post Merged at 01:12 AM ----------

(page3 of this thread)
 
yeah done that ok but got an error message and wooshman was tired so we leaving the rest until tomorrow now



ere Buck tell me summit will ya, should i not be using filezilla or DCC or something at this stage of the set up???
 
Last edited:
the error shouldn't affect the line. i had the same problem but could still out the line on box. had all channels working just couldn't use timeshift (pause, rewind, record)
 
image.jpg

---------- Post Merged at 01:43 AM ----------

excused the sideways pic. took on my phone lol, you need to be there and you tried that yeah?

---------- Post Merged at 01:45 AM ----------

obviously mine says active mgcamd as i have an nline
 
yeah thats what mine looks like too and says:
active CAM1:CCcam2.3.0

then it says no ECM info and changes to say No new ECM info.
red stop
green restart
yellow CCcaminfo
blue install
 
no, just trying to rule things out

---------- Post Merged at 02:19 AM ----------

found this by sucmnsee. I've exhausted my knowledge again lol you could give this a try if you're feeling nocturnal.

other than that it looks like you'll have to hold out for tomorrow when Woosh comes online

U can run ur CCcam.cfg on these no probs when u first get it. Then worry about perfect way later.
you'll need an ftp program on pc to send over ur router to the box. I find dreambox control centre best. SSimple with steps

Google dreambox control centre.
download to pc and install.
open it.
middle right of screen click search
new window click search
wait untill u c ur box ip address is found
dbl click the ip address of box
window disappears
click reconnect
should say telnet, ftp, enigma 2 connected
bottom left click ftp
opens window.
left pane is box
right pane is pc.
find ur CCcam.cfg in right panel wherever on ur pc.
dbl click etc folder in left pane
single click ur CCcam.cfg in right pane
click arrow in middle pointing left
yes to replace

The rest depends on what box software image u want to run. But loads of people here to help

---------- Post Merged at 02:21 AM ----------

Not sure that will be much use as by the looks of it the line is on the box just not working. I think woosh will probably test the line himself for you. It's sounding like an issue with that but i can't be sure
 
no, just trying to rule things out

---------- Post Merged at 02:19 AM ----------

found this by sucmnsee. I've exhausted my knowledge again lol you could give this a try if you're feeling nocturnal.

other than that it looks like you'll have to hold out for tomorrow when Woosh comes online

U can run ur CCcam.cfg on these no probs when u first get it. Then worry about perfect way later.
you'll need an ftp program on pc to send over ur router to the box. I find dreambox control centre best. SSimple with steps

Google dreambox control centre.
download to pc and install.
open it.
middle right of screen click search
new window click search
wait untill u c ur box ip address is found
dbl click the ip address of box
window disappears
click reconnect
should say telnet, ftp, enigma 2 connected
bottom left click ftp
opens window.
left pane is box
right pane is pc.
find ur CCcam.cfg in right panel wherever on ur pc.
dbl click etc folder in left pane
single click ur CCcam.cfg in right pane
click arrow in middle pointing left
yes to replace

The rest depends on what box software image u want to run. But loads of people here to help

---------- Post Merged at 02:21 AM ----------

Not sure that will be much use as by the looks of it the line is on the box just not working. I think woosh will probably test the line himself for you. It's sounding like an issue with that but i can't be sure


seriously starting to think i have been scammed by the person i got the "GIFT/LINE" from.........
 
unfortunately that's what i'm thinking. But let's be optimistic and hope that's not the case, however it could also be something really stupid and small that you've missed or changed. fingers crossed!!

---------- Post Merged at 02:45 AM ----------

That's me done for the night. I hope to see you're all up and running tomoz and finally enjoying full sly :D GET SOME SLEEP
 
unfortunately that's what i'm thinking. But let's be optimistic and hope that's not the case, however it could also be something really stupid and small that you've missed or changed. fingers crossed!!



:sorrow::sorrow::sorrow::sorrow::sorrow::sorrow::sorrow::sorrow::sorrow::sorrow::sorrow::sorrow::sorrow::sorrow::sorrow:

---------- Post Merged at 02:47 AM ----------

right off to bed now as im up at 6:45 am

na night Buck x
 
Back
Top