See my post aboveTried to use FileZilla to access the box and it was saying password was incorrect???
Tried password and pass but still saying incorrect and wanted a password - any ideas why???
See my post aboveTried to use FileZilla to access the box and it was saying password was incorrect???
Tried password and pass but still saying incorrect and wanted a password - any ideas why???
Menu Setup System Network Password Setup Enter new password. Save with the green buttonTried to use FileZilla to access the box and it was saying password was incorrect???
Tried password and pass but still saying incorrect and wanted a password - any ideas why???
So once I install Grog again where would I put my line and how would I activate OScam? I know where the line goes in MGcam and CCcam but I have never used OSCAM so forgive my ignorance. Been doing this for years but never could get mt head around OSCAM :-)on my VU+ its 5 -6 minutes, on a zgemma h2 it could take 20 miniutes lol
if you have oscam-emu installed then your oscam files go in /etc/tuxbox/config/oscam-emu folder on the box.So once I install Grog again where would I put my line and how would I activate OScam? I know where the line goes in MGcam and CCcam but I have never used OSCAM so forgive my ignorance. Been doing this for years but never could get mt head around OSCAM :-)
I'm using a Zgemma H2H with only Virgin no Sky.
And thanks for your help I do appreciate it.
Thank youin ATV 6.4 you need to set a password before you can FTP. menu -> setup -> System -> Network -> Password
Once set use username root and password you set above in filezilla
Thank you
i was able to access into the box via FileZilla after your advice on setting up a password
i tried to enter Oscam editor on Webif but now this does not connect I tried :8888/:88/ I did get in earlier this morning
with :83 but now nothing
Yippee ok yes I can see the Oscam webinterface nowif you load openwebif on the left in the extras section is there a link to oscam webinterface? if so click on it.
If you put your line in newcamd file then you should be running Mgcam as your softcamYippee ok yes I can see the Oscam webinterface now
so I entered my line using filezilla in key - newcamd - cws
i also entered the script that I was sent into Oscam server restarted the box but channels blank
Thanks for the replies guysIf you put your line in newcamd file then you should be running Mgcam as your softcam
Try that and restart to see what happens
You won’t need to access oscam panel if you run mgcamThanks for the replies guys
its strange earlier I was able access Oscam web interface then restarted the box and now I can’t get the Oscam webinterface
in Webif I just see the standard Webif but no Oscam webinterface on the left side
why is this
appreciate your help so far guys
You won’t need to access oscam panel if you run mgcam
Hi Guys
Followed dsayers instructions and sat line working on mgcamd but cant get it to work on oscam?
Below is the config file, have i missed anything?
[reader]
label = Sly_line
protocol = newcamd
device = sat.name.net,41190
key = 0102030405060708091011121314
user = user
password = pass
disableserverfilter = 1
connectoninit = 1
caid = 1841
group = 1
[reader]
label = VM_line
protocol = newcamd
device = vm.line.org,61007
key = 0102030405060708091011121314
user = user
password = pass
disableserverfilter = 1
connectoninit = 1
caid = 1841
group = 1
emmcache = 1,3,2,0
blockemm-unknown = 1
dropbadcws = 1
disablecrccws = 1
[reader]
label = emulator
protocol = emu
device = emulator
disablecrccws_only_for = 0E00:000000
caid = 0500,0604,0E00,1010,1801,2600,2602,2610,1841
detect = cd
ident = 0500:000000,007400,007800,021110,023800;0604:000000;0E00:000000;1010:000000;1801:000000,001101,002111,007301;2600:000000;2602:000000;2610:000000
group = 1
emmcache = 2,1,2,1
dropbadcws = 1
disablecrccws = 1
emu_auproviders = 0604:010200;0E00:000000;1010:000000;2610:000000
You need to make sure your running the oscam softcam then try to access openwebif and you should see the oscam interface.I tried with mgcam like You said in your earlier post I restarted the softcam and switched box off and then on again
but no luck
i don’t understand why I the oscam webinterface does not show up in Webif
I can access the Webif page with just the standard screen with settings, terminal etc
thanks for your advice guys
will give it a go again tomorrow
I’ve noticed it’s mainly cinema channels...I get a bit of freezing too on channels