Sat situation is the same as your own, HOWEVER, VM lines for ROI are as rare as rocking horse poop.The first list you get is Sat region, once you have selected that you then have the cable options for RoI
No RoI region for sat is my oversight and needs fixing. Select any region and come back here so we can help you if needed to setup Sat for RoI. From what I know there is nothing left on Sat for RoI though. I could be wrong.
@wheelo will be able to answer this for us.
tremendous build Wooshman!
Been using Sucmnsee Vix for 3 years or so and was long overdue a change. Got my Zgemma star H2 flashed and ready to go but i'm struggling
to get my line going. i'm going very wrong somewhere.
i've been using file zilla and also trying all the soft cam options but still no joy.
my line normally looks something like this;
CWS = ????????????????????????????????????????????? 01 02 03 04 05 06 07 08 09 10 11 12 13 14
what softcam should i run it through? And if i need to edit the line what should it look like?
been at this for more hours than i'd care to admit at this point.
any help from anyone would be greatly appreciated.
thanks
Line still has 3 months left and was working earlier on before i foolishly started meddling about! I've probably changed something i shouldn't have.....again. might just revisit this again tomorrow. re install again afresh. thanks for the tipshow long have you had the line?
is there a chance it's expired?
if mcgamd is installed already and the line's not working it looks like either the line has expired or the softcam could be a duffer
i think you just need the normal extreme editor which is in system plugins at the bottom of the list install it and send the code to your supplierhi guys,
it,s been a couple of years since i dabbled in the sat game.just got an urge to give it a go again.
so forgive me as im a little rusty and things have changed somewhat since i have been away from the game.
have a Vu uno 4k,and have a working iptv line.(i managed to get it to work on an old vu zero box using extream plugin)
i have infinity installed on the box and downloaded the xtream plugin (arm based one),when i tried to install the line into the plugin it tells me to contact my supplier (or something like that),i contacted him and he maintains his side is ok and the file he sent me for the vu 4k is the correct file (arm based).
hope this all makes sense.
is the procedure im using ok or am i doing something wrong (i must be wrong) other wise it should work.
flashing the box was very simple (hat,s of to the developers).any help to get this working would be very greatfull.
of to work now will check back when i get home,tks guys.
No change, just the little progress circle on top of tv screen and digits recyclying on the Sat Boxwhen its on wi screen try pressing channel 1 on remote
That's my problem, I cant reflash my backup, or an alternative backup that definitively good. It stays on the wooshbuild Infinity permanent loop. I can see that the box is connected to my wifi router, but it refuses my connection.you must have done summet wrong flash open atv again and when it gets to the part were you have to use remote to setup hdmi on your tv screen don't do anything go to your computer laptop or tablet and type the ip address of your box in your browser right at the top of page on computer then enter and web if will pop up then go to first page on this thread and click link for wi and start from 1
That's exactly what im saying, ive tried doing a reflash with four different usb drives, see my first post, and it still just shows the WI screen! No matter what I try I still get "Run Alpha+", followed by booting then a series of two digit numbers starting at -00- and reaching -97- before recycling. At no stage does it say "flash".your better setting box up first with wired connection and what do you mean you cant reflash just put latest open atv on a usb stick turn box off put usb in turn back on and flash with my zgemma when I turn it back on I have to press start button on front of box then it will say flash