Zgemma H5. 2tc how do make Freeview only

[pabloescaban]

I done a service scan got the ch working but there all ch are mix up how do I organise the channels thank

Use autobouquetmaker scan
open autobouquetmaker/providers and set freeview to your region:

then save and press green to scan

 

[Fusion]

I keep gein
Autobiuqyetmaker
Failed to tune Freeview UK on tuner c

 

[pabloescaban]

I keep gein
Autobiuqyetmaker
Failed to tune Freeview UK on tuner c

Go to tuner config
click on tuner C, where it says DVB/C make sure this is set to nothing connected:

Then click the right arrow and it will change to DVB/T, set this to your transmitter/region and then click green to save:

 

[grog68]

I keep gein
Autobiuqyetmaker
Failed to tune Freeview UK on tuner c

enter your postcode at wolfbane.net and try some of the transmitters it lists in the results in ABM

 

[Fusion]

Autobiuqyetmaker
Failed to tune Freeview UK on tuner b now

 

[pabloescaban]

Autobiuqyetmaker
Failed to tune Freeview UK on tuner b now

Yes, you have to do the above on both tuners if not using VM cable in the box

 

[Fusion]

enter your postcode at wolfbane.net and try some of the transmitters it lists in the results in ABM

Try that not working

 

[Fusion]

Only way I can get to ch in is use service scan i get 173ch alll the ch in but there mix up
Autobiuqyetmaker not work for me

 

[Fusion]

AutoBouquetsMaker
Failed to tune Freeview UK on tuner c
Please check the following:
The tuner is correctly configured.
You can receive the specified frequency.

 

[pabloescaban]

AutoBouquetsMaker
Failed to tune Freeview UK on tuner c
Please check the following:
The tuner is correctly configured.
You can receive the specified frequency.

Are you using it for just freeview?
No vm cables attached?
Whichever tuner your aerial is plugged into is set to dvb/c "nothing connected"
The other tuners can be set to "not configured"
Then run abm scan

 

[Fusion]

Just Freeview only
Nor vm cables attached
tuner your aerial is plugged
Set the two tuners into is set to dvb/c "nothing connected"??

 

[grog68]

Just Freeview only
Nor vm cables attached
tuner your aerial is plugged
Set the two tuners into is set to dvb/c "nothing connected"??

Should be set to DVB T2. not dvb c

 

[Fusion]

All done now thank yous for your time lads

 

[baz12]

All done now thank yous for your time lads

just a bit of confusion - fusion
glad you sorted m8

 

[Fusion]

In AutoBouquetsMaker scan there was two I had to turn one off and set of the North East to make it work

 

[adamsm]

I set tuners for all UK and then used DVB-T frequency finder. It will create your region in providers in my case Yorkshire tick that and then start scan in auto bouquet maker.

 

[grumpyass]

Lol I must be losing my marbles. A few months ago I was reverting back to turning it in to just a freeview box. Had it before and just could not figure out why it was not finding the channels. Gave up and just used the tuner in the TV. After reading this I now know I did not put the ariel in lol, dumbass.

 

[pabloescaban]

Lol I must be losing my marbles. A few months ago I was reverting back to turning it in to just a freeview box. Had it before and just could not figure out why it was not finding the channels. Gave up and just used the tuner in the TV. After reading this I now know I did not put the ariel in lol, dumbass.

No one would call you a dumbass but we were all thinking it very loudly😏

 

[loncell]

I use my old mounted sat dish and put it into the sat tuner and run abm. There's quite alot if stations on freeview for sat

 

[gray1313]

I set tuners for all UK and then used DVB-T frequency finder. It will create your region in providers in my case Yorkshire tick that and then start scan in auto bouquet maker.

were di i find DVB-T frequency finder