What's new
By:

"idiots guide" to installing sucmnsee's image with EVERY step explained in detail

Not sure if this will help, but,
I had this happen a few times, I removed the cables, removed F plugs, cut down the cable, replaced F plugs and snipped the copper wire so it wasn't protruding above the F plug too much - not had a problem since.

You won't get any subscribed channels showing until MGcamd is running correctly, sometimes you need to stop it and then start again particularly after making a few changes.
 
Last edited:
Many thanks to Tich who talked me through the setup only to find the box seems to have a faulty tuner, thanks to everyone else who helped too!

************* UPDATE - I have now purchased a new box and found that the problem was not with the instructions but with a faulty box, got the new box up and working within 40 minutes ****************************
 
Last edited:
mark5211 said:
Many thanks to Tich who talked me through the setup only to find the box seems to have a faulty tuner, thanks to everyone else who helped too!
Click to expand...

Glad you got figured it out. Sometimes we forget that problems may not be user error but down to faulty equipment. I think we had just got used to things working.
 
I can't find my old post but I'm in the middle of doing the Fat32 format as I've just done the LowLevel format.. I have no idea what the LowLevel one is meant to do but did that anyway. While I'm waiting can someone send me the link to the SKY Bule HD so I can flash once the format has finished? Also Do I need to plug in the Ethernet cable for the flash.. Or when do I plug in the Ethernet cable?

Regards Jay
 
itsmrjt said:
I can't find my old post but I'm in the middle of doing the Fat32 format as I've just done the LowLevel format.. I have no idea what the LowLevel one is meant to do but did that anyway. While I'm waiting can someone send me the link to the SKY Bule HD so I can flash once the format has finished? Also Do I need to plug in the Ethernet cable for the flash.. Or when do I plug in the Ethernet cable?

Regards Jay
Click to expand...

The sky skin is already on the box Blue HD makes the box run slower the skin pre-installed is perfect sky like why change it?
 
tried to flash my Zgemma s2 and it just went to boot and loads channels.. It don't start flash like you said.
 
itsmrjt said:
tried to flash my Zgemma s2 and it just went to boot and loads channels.. It don't start flash like you said.
Click to expand...

The file you downloaded did you un-zip until the file just said Zgemma?

as that's the folder you need to add to the USB.

if you did the box does not like your USB
 
I downloaded the lastest update and its not in a zip/rar file..?

---------- Post Merged at 03:41 PM ----------

I've tried.. 4 times and nothing.. tried a mtpockets_zgemma2 zip and it's just going Boot, then Loads with numbers.. No flash on the box.. Can anyone help with this plz
 
itsmrjt said:
I downloaded the lastest update and its not in a zip/rar file..?

---------- Post Merged at 03:41 PM ----------

I've tried.. 4 times and nothing.. tried a mtpockets_zgemma2 zip and it's just going Boot, then Loads with numbers.. No flash on the box.. Can anyone help with this plz
Click to expand...

Sounds like a USB problem . try doing a low level format with HDD guru and then a full windows format fat32.
 
Ok on the downloads page I tried.

ackup of Vix Hades 018 01/09/15 for zgemmastar 2s - didn't flash.. Just went to boot then loaded like channels.

Then tried mtpockets and that didnt flash

Backup of Vix Apollo 165 10/06/15 for zgemmastar 2s did flash and now says tune failed as I've not added my line.
 
Quick question trying to do the update the newcamd.list file, but my line starts C: AABBCCBBCC etc so would the file start:

CWS = C: AABBCCBBCC etc

or

C: AABBCCBBCC etc

Thanks
 
If it's a C line just put line complete into ect folder CCcam. cfg you only change CWS . = when using MG Camd and using N lines


Sent from my iPhone using Tapatalk
 
You must log in or register to reply here.
Back
Top